Sources
Help build the largest human-edited directory on the web.
Submit a site - Become an editor
Wikipedia. Licensed under the GNU Free Documentation License.
Are you an expert in this subject? Join the discussion and share your knowledge at Wikipedia.org.
Wave soldering
From Wikipedia, the free encyclopedia
Wave soldering is a large-scale soldering process by which electronic components are soldered to a printed circuit board (PCB) to form an electronic assembly. The name is derived from the fact that the process uses a tank to hold a quantity of molten solder; the components are inserted into or placed on the PCB and the loaded PCB is passed across a pumped wave or cascade of solder. The solder wets to the exposed metallic areas of the board (those not protected with solder mask), creating a reliable mechanical and electrical connection. The process is much faster and can create a higher quality product than manual soldering of components.
Wave soldering is used for both through-hole printed circuit assemblies, and surface mount. In the latter case, the components are glued onto the printed circuit board surface before being run through the molten solder wave.
As through-hole components have been largely replaced by surface mount components, wave soldering has been supplanted by reflow soldering methods in many large-scale electronics applications. However, there is still significant wave soldering where SMT is not suitable (e.g. large power devices and high pin count connectors), or where simple through-hole technology prevails (certain major appliances).
Contents |
There are many types of wave solder machines, however the basic components and principles of these machines are the same. A standard wave solder machine consists of three zones: the fluxing zone, the preheating zone and the soldering zone. An additional fourth zone, cleaning, is used depending on the type of flux applied.
The printed circuit board with through-hole components on top of the board and/or surface mount components glued on the bottom side are sometimes placed on a fixture. The fixture is a fiberglass composite or titanium frame with openings exposing the components to be soldered. Wave solder fixtures are required for PCB's where bottom side components cannot be exposed to the solder, or the board is either too small or has a non rectangular shape and cannot be 'picked up' by the titanium fingers. The fixtures can also be used to incorporate clamping and alignment devices designed to hold components in place and prevent 'lifting' of the components as the leads hit the wave, whilst ensuring correct vertical alignment. The fixture is then placed on a conveyor which will carry the PCB through the machine. The conveyor consists of titanium fingers. Titanium is used because solder will not adhere to this metal.
The introduction of RoHS and the subsequent development of lead free solder (which has a much higher melting point than conventional solder), has caused problems for the manufacturers of material used in fixtures. The higher temperatures causes resin burn out which, in turn, compromises the structural integrity of the fixture. This has created a significant challenge to the manufacturers of both the material and fixtures.
The PCB will then enter the fluxing zone, which applies flux to the underside of the board. Two types of fluxers are used: the spray fluxer and foam fluxer.
Some spray fluxers consist of a robotic arm which travels from side to side while spraying a fine mist of flux onto the bottom side of the board. Other spray fluxers consist of a stationary bar with a series of nozzles that spray a fine mist. There are also additional ones that can consist of a single stationary ultrasonic head and/or an oscillating ultrasonic head. Some systems will then use compressed air to remove excess flux or to completely remove flux from some areas.
The foam fluxer consists of a tank of flux into which a plastic cylinder with tiny holes is immersed; this is sometimes called a "stone". The plastic cylinder is covered with a metal chimney. Air is passed through this cylinder which causes flux foam to rise up the chimney, forming a cascading head of foam. As the PCB passes over the foam head, flux is applied to the PCB.
For either flux application method, precise control of flux quantities are required. Too little flux will cause poor joints, while too much flux may cause cosmetic or other problems.
The PCB will then enter the preheating zone. The preheating zone consists of convection heaters which blow hot air onto the PCB to increase its temperature. For thicker or densely populated PCBs, an upper preheater might be used. The upper preheater is usually an infrared heater.
Preheating is necessary to activate the flux, and to remove any flux carrier solvents. Preheating is also necessary to prevent thermal shock. Thermal shock occurs when a PCB is suddenly exposed to the high temperature of the molten solder wave from the ambient room temperature.
The tank of molten solder has a pattern of standing waves (or, in some cases, intermittent waves) on its surface. When the PCB is moved over this tank, the solder waves contact the bottom of the board, and stick to the solder pads and component leads via surface tension. Precise control of wave height is required to make sure solder is applied to all areas but does not splash to the top of the board or other undesired areas. This process is sometimes performed in an inert gas atmosphere to increase the quality of the joints.
Some types of flux, called "no-clean" fluxes, do not require cleaning; their residues are benign after the soldering process. Others, however, require a cleaning stage, in which the PCB is washed with solvents and/or deionized water to remove flux residue.
Due to the precise requirements needed for wave soldering, the soldering equipment must be closely monitored. Common tests include visually inspecting boards for signs of problems with the soldering process, a resistance test to make sure no flux or other deposits are causing conduction between traces, halide content tests to check for proper flux activation, and others. In modern equipment, virtually all control of the process is computerized, and little human interaction is needed to monitor and adjust the equipment.
- Tour of a motherboard factory, including pictures of a wave soldering machine
- Example of wave soldering machines (links to manufacturers)
- Use of composites in wave solder pallets - An informative article from Composites World on the use of composite materials in the manufacturing of wave solder pallets.
- RoHS and its impact on the use of composite materials in the manufacture of wave solder pallets An in-depth discussion on the problems of lead free solder and fixture design.
- Design rules for Selective Wave Solder Pallets An interesting article on the design of wave solder pallets.
- Examples of manufacturers of wave solder pallets (with photos)