From Wikipedia, the free encyclopedia

This article deals with the device used in electronics labs. There is also an article on optical breadboards used in optics labs. For the food preparation utensil, see Cutting board.

A breadboard with a completed circuit

A breadboard is a reusable solderless device used to build a (generally temporary) prototype of an electronic circuit and for experimenting with circuit designs. This is in contrast to stripboard (veroboard) and similar prototyping printed circuit boards, which are used to build more permanent prototypes or one-offs, and cannot easily be reused. A typical breadboard will have strips of interconnected electrical terminals, known as bus strips, down one or both sides—either as part of the main unit or as separate blocks clipped on—to carry the power rails.

A modern solderless breadboard consists of a perforated block of plastic with numerous tin plated phosphor bronze spring clips under the perforations. Integrated circuits (ICs) in dual inline packages (DIPs) can be inserted to straddle the centerline of the block. Interconnecting wires and the leads of discrete components (such as capacitors, resistors, inductors, etc.) can be inserted into the remaining free holes to complete the circuit topology. In this manner, a variety of electronic systems may be prototyped, from small circuits to complete central processing units (CPUs). However, due to large stray capacitance (from 2-25pF per contact point), solderless breadboards are limited to operating at relatively low frequencies, usually less than 10 MHz, depending on the nature of the circuit.

A binary counter wired up on a large breadboard

A breadboard is used to design a circuit for a miniature toy traffic light. Note how the circuit is generally early in the design process, as an inefficient power supply is being used at this time. As the circuit becomes more refined, a more appropriate power supply is likely to be chosen, such as two AA batteries.

The breadboard derives its name from an early form of point-to-point construction. In the early days of radio, amateurs would nail copper wire or terminal strips to a wooden board (often literally a board for cutting bread), and solder electronic components to them. Sometimes a paper schematic diagram was first glued to the board as a guide to placing terminals, components and wires.

Alternative methods to create prototypes are point-to-point construction, reminiscent of the original breadboards, wire wrap, and boards like stripboard. Complicated systems, such as modern computers comprising millions of transistors, diodes and resistors, do not lend themselves to prototyping using breadboards, as sprawling designs on breadboards can be difficult to lay out and debug. Modern circuit designs are generally developed using a schematic capture and simulation system, and tested in software simulation before the first prototype circuits are built on a printed circuit board. Integrated circuit designs are a more extreme version of the same process: since producing prototype silicon is expensive, extensive software simulations are performed before fabricating the first prototypes. However, breadboard prototyping techniques are still used for some specialised applications such as broadband RF circuits, or where software models of components are inexact or incomplete.

A breadboard prototype (also known as an evolutionary prototype) is an iteratively designed piece of software designed to evolve into a full-fledged system. This contrasts with a throwaway prototype (often associated with a proof-of-concept) that is discarded.

• Lego Electronic Lab Kit
• Progressive Wiring Techniques
• PCB router, PCB router PCB router
• wire wrap
• dead bug
• "rat's nest"
• Effects Building Techniques lists several other techniques
• Using any available piece of metal as a common junction between parts

The name Breadboard comes from the old practice of using a wooden board (a real "bread-board") and hammering in small bronze nails, or thumb-tacks, to which the leads of electronics components would be soldered.

The hole pattern for a typical etched prototyping PCB (printed circuit board) is similar to the node pattern of the breadboard shown above, rotated 90°.

The integrated circuit for the Polaroid SX-70 camera was breadboarded before Texas Instruments fabricated the custom chip. It was rumoured to have been built from discrete components on a 4 ft. x 8 ft. piece of plywood, and was fully functional. The project was so secret that Texas Instruments engineers were only given functional specifications, but not told the purpose of the chip.^{[citation needed]}

• Printed Circuit Board
• Stripboard
• Perfboard
• Iterative design

• Java applet breadboard simulator